Roof Flashings for Metal Roofs

Oatey® invented the flashing industry more than 100 years ago. Today Oatey Flashings are used in commercial and residential applications where a water-tight seal around plumbing vent pipe or outside wall penetrations is required. Oatey Master Flash® Roof Flashings are engineered for metal roof applications for any pitch. Easily customized to accommodate a broad range of pipe diameters.
* MASTER FLASH® is a Registered Trademark of the Aztec Washer Company, Inc.

loading...
Filter by
Product Type
Showing 3 of 3
038753140568_H_001.jpg - Oatey® .25 in. – .75 in. Master Flash® 4.5 in. x 4.5 in. Base Roof Flashing

Oatey® Master Flash® Roof Flashings

Black

Plastic

Oatey

Master

No

0.25 in. - 2 in.

0.15 lb.

4.5" X 4.5"

Engineered for profiled roofing systems at any pitch

Pliable material won't crack or break

Use silicone sealant between base and surface, and secure with sheet metal screws

Easily customized to accomodate a broad range of pipe diameters

Non-fading EPDM collar provides maximum

0.25 in. - 4 in.

0.45 lb.

8" X 8"

Non-fading EPDM collar provides maximum resistance to weathering caused by ozone and UV rays

Rated to withstand 212°F continuous heat and approved for Type B installations; intermittent temperature resistance to 275°F

Closed to 5-3/4 in. Master Flash® EPDM roof flashing

8 in. x 8 in. soft aluminum base for profiled metal roofs

For any panel configuration, roof pitch or pipe location

Molds to all types of roofing surfaces, including metal, plastic, tile and rubber membrane

Marked cut lines allow for easy installation and customization for various pipe sizes with a sharp knife or scissors

Slide over pipe, use silicone sealant between base and surface, then secure with sheet metal screws

MASTER FLASH® is a Registered Trademark of the Aztec Washer Company

3 in. - 6 in.

0.75 lb.

10" X 10"

Engineered for profiled roofing systems at any pitch

Pliable material won't crack or break

Use silicone sealant between base and surface, and secure with sheet metal screws

Easily customized to accomodate a broad range of pipe diameters

Non-fading EPDM collar provides maximum

5 in. - 9 in.

1.2 lb.

12" X 12"

Engineered for profiled roofing systems at any pitch

Pliable material won't crack or break

Use silicone sealant between base and surface, and secure with sheet metal screws

Easily customized to accomodate a broad range of pipe diameters

Non-fading EPDM collar provides maximum

4 in. - 8.25 in.

0.9 lb.

11" X 11"

Engineered for profiled roofing systems at any pitch

Pliable material won't crack or break

Use silicone sealant between base and surface, and secure with sheet metal screws

Easily customized to accomodate a broad range of pipe diameters

Non-fading EPDM collar provides maximum

6 in. - 11 in.

1.5 lb.

14" X 14"

Engineered for profiled roofing systems at any pitch

Pliable material won't crack or break

Use silicone sealant between base and surface, and secure with sheet metal screws

Easily customized to accomodate a broad range of pipe diameters

Non-fading EPDM collar provides maximum

7 in. - 13 in.

2.2 lb.

17 x 17 in

Engineered for profiled roofing systems at any pitch

Pliable material won't crack or break

Use silicone sealant between base and surface, and secure with sheet metal screws

Easily customized to accomodate a broad range of pipe diameters

Non-fading EPDM collar provides maximum

1.25 in. - 3 in.

0.3 lb.

6" X 6"

Engineered for profiled roofing systems at any pitch

Pliable material won't crack or break

Use silicone sealant between base and surface, and secure with sheet metal screws

Easily customized to accomodate a broad range of pipe diameters

Non-fading EPDM collar provides maximum

10 in. - 18 in.

2.95 lb.

25 x 25 in

Engineered for profiled roofing systems at any pitch

Pliable material won't crack or break

Use silicone sealant between base and surface, and secure with sheet metal screws

Easily customized to accomodate a broad range of pipe diameters

Non-fading EPDM collar provides maximum

14751.jpg - Oatey® 1/4 in. – 4 in. Retro Master Flash® 8 in. x 8 in. base

Oatey® Retro Master Flash® Roof Flashings

Black

Plastic

Oatey

Master

No

0.25 in. - 4 in.

0.6 lb.

8" X 8"

Flexible base conforms to most flat or contoured roof surfaces including clay tile and metal roofs, sliding over vent pipe with pitch from 0-45°

1-1/4 in. to 4 in. Retro Master Flash® EPDM roof flashing

8 in. x 8 in. soft aluminum base for profiled metal roofs

Easily customized to accommodate use on multiple pipe sizes

Most commonly used with an existing roof penetration, when installing a flashing over the pipe is not an option and requires a hard-to-reach or wrap-around installation

Marked cut lines allow for easy installation and customization for various pipe sizes with a sharp knife or scissors

Slide over pipe, use silicone sealant between base and surface, then secure with sheet metal screws

MASTER FLASH® is a Registered Trademark of the Aztec Washer Company

Do not use petroleum based products on Retro Master Roof Flashings

Non-fading EPDM collar provides maximum resistance to weathering caused by ozone and UV rays

Rated to withstand 212°F continuous heat and approved for Type B installations; intermittent temperature resistance to 275°F

0.25 in. - 4 in.

0.6 lb.

12" X 15"

Do not use petroleum based products on Retro Master Roof Flashings

Retro Master Flashing slides over vent pipe for pitch to 45 degrees

Flexible base conforms to most flat or contoured roof surfaces including clay tile and metal roofs

Approved for Type B installations

Master Boot is made of EPDM and compounded specifically for maximum resistance to weathering due to ozone and ultraviolet light

Master Boot is easily customized with a sharp knife or scissors to accommodate a broad range of pipes and vent diameters

Continuous Temperature Resistance to 212 F Intermittent Temperature Resistance to 275 F

4 in. - 9.25 in.

1.5 lb.

14" X 14"

Do not use petroleum based products on Retro Master Roof Flashings

Retro Master Flashing slides over vent pipe for pitch to 45 degrees

Flexible base conforms to most flat or contoured roof surfaces including clay tile and metal roofs

Approved for Type B installations

Master Boot is made of EPDM and compounded specifically for maximum resistance to weathering due to ozone and ultraviolet light

Master Boot is easily customized with a sharp knife or scissors to accommodate a broad range of pipes and vent diameters

Continuous Temperature Resistance to 212 F Intermittent Temperature Resistance to 275 F

9 in. - 19 in.

2.4 lb.

11" X 14.5"

Do not use petroleum based products on Retro Master Roof Flashings

Retro Master Flashing slides over vent pipe for pitch to 45 degrees

Flexible base conforms to most flat or contoured roof surfaces including clay tile and metal roofs

Approved for Type B installations

Master Boot is made of EPDM and compounded specifically for maximum resistance to weathering due to ozone and ultraviolet light

Master Boot is easily customized with a sharp knife or scissors to accommodate a broad range of pipes and vent diameters

Continuous Temperature Resistance to 212 F Intermittent Temperature Resistance to 275 F

There are no results available